Every plush toy must be plated before mass production, which means that you need to make a sample. In the process of making the sample, what problems will occur, how can it be improved, so the process of playing the board is very important. But what kind of process is it, what should you pay attention to? First, when the customer provides drawings or manuscript paper to the plush toy manufacturer, the designer needs to correctly identify the requirements of the original template, and then distinguish the materials and process methods corresponding to the template according to the requirements. For example, the cutting method, if the template needs to be punched, the knife mold should be made; if the hot velvet sample is needed, the hot melt plate should be made; if the cutting is normal, the sample plate should be made for cutting. Generally, the materials for the sample are made: 200 cardboard for the original sample; and 0.8 mm elastic paper for the production sample. The sample paper should be flat, clean and dry. Second, when making a toy model, you must pay attention to the principle of the straight line, arc, angle, proportion, symmetry, and positioning of the sample. The text is written on the front of the sample. The straight line is straight, the arc is round, the knife eye is in place, the angle and the ratio are the same. These points are the principle of making the model. Patterns with trapezoidal and other center lines should be symmetrical on both sides; the rectangular pattern should be parallel to the side lines. The positioning point must be accurate, and the positioning points used for splicing or saving should be corresponding, and there is no omission. Third, copy the production template should be accurate, and must be consistent with the original template. There must be no error in the length of the sample below 10cm, and the error is allowed to be within 0.5cm. In order to maintain the accuracy of the template and check the deformation of the template, it is necessary to repeatedly check the original template during use. If there is any non-conformity, it should be replaced in time. When the fabric is cut, there will be errors due to the difference in the material or process of the fabric. Consider enlarging or reducing the template, but this needs to be confirmed by the seal. Fourth, in order to facilitate the correct identification of the template, the logo of the template is very important. The logo of the sample includes: product model, product name, part name and template number, material name (process processing requirements). The yarn flow direction, the number of pieces, the positioning marks, etc. must all be marked on the sample board. If the sample area is too small to mark all the contents, the template number can be marked, and the technical requirements can be made. Find the corresponding content on the single. Fifth, copying the accuracy of the production prototype is a prerequisite for ensuring the accuracy of the piece. The quality requirements for copying the template are: accurate shape, correct logo, and complete information. Sixth, the discharge plan is an indication of the arrangement of each sample in the minimum amount of material used. The discharge diagram generally indicates the general information of the filament flow or the direction of the sample, the reverse alignment of the template, or the alignment of the same direction and the patterning of the template. Seventh, the cutting operation should be based on the information indicated in the discharge diagram, according to the requirements of the production batch, calculation and discharge, calculate the unit piece volume. Discharge in the least amount of material. Eighth, after cutting, you can carry out the sewing, eye-catching, filling and other processes, and finally make the model. Compare with the drawings, what problems and errors occur, and then improve. The products are environmentally friendly, with excellent workmanship, complete supporting facilities, advanced technology, perfect management, high quality, reasonable price, fast development, strict confidentiality and complete after-sales. And the company has passed ISO9001 certification. Meet the higher requirements of customers and escort. Only a detailed product drawing (or sample) is required to provide customers with a one-stop service from development to after-sales. Sincerely look forward to the majority of domestic and foreign customers to visit the guide, negotiate business, and work together for a win-win situation. Dongguan Hongyuan Toys Co., Ltd. Focus on a professional business mascot, plush dolls, artificial animal toys, fabric toys, children's backpacks, game peripheral dolls, pillow cushions and other products design, production, customization, as a plush toy fabric manufacturer, to provide your company with personality Customized plush toys! Make your sign brighter and make your brand more famous! Choose Hongyuan Toys and believe in the power of word of mouth! Garden Edging,Lawn Edging,Corten Steel Garden Edging,Flower Bed Edging Henan Jinbailai Industrial Co.,Ltd , https://www.designsteelarts.com