The construction of sports wood floors is a common technique. The following small series introduces the construction process of sports wood floors and the common problems during installation. Construction process 1, construction conditions (1) Physical exercise Before the construction of the wooden floor, the civil engineering project must be completed and cleaned up to meet the architectural design requirements. (2) The installation of indoor water, electricity, steam, and ventilation is completed, and the water network pipeline must be pressure tested. (3) The interior roofing, ultrasonics, electroacoustics, lighting and other projects are completed. (4) The ground humidity and the equilibrium moisture content are consistent with the outside world. (5) If cross-construction occurs, Party A needs to make a unified arrangement. 2, construction preparation (1) Construction tools and equipment are ready. (2) Construction materials must be shipped to designated locations and stored according to product characteristics. (3) Inspection of construction conditions, and records of matters that do not meet construction requirements. (4) Construction progress and management system development. (5) Strengthen fire prevention education to prevent accidents. 3, draw keel and pad position line. 4. The level gauge detects the height difference of the cement floor at the reference point. 5. Install a 50mm thick pad at the reference point. The error of the reference pad elevation should not exceed 1mm. 6, install the keel. 7. Cooperate with civil construction units to install floor embedded parts. 8. Stagger the multi-layer solid wood wool floor, spread it on the keel, and fasten it with the floor nail. 9. Spread the moisture-proof mat on the wool floor. 10. The floor surface is nailed to the wool floor and requires a straight line in the longitudinal direction. 11, in the surface layer with a grinding machine to polish, require a 3 meter ruler to measure the height difference within 3mm, the error and then polish and smooth. 12. Lacquer the floor covering, a layer of primer, two layers of paint. Sports wood floor installation FAQ 1. The reason for the sound of empty drums is due to the fact that it is not fixed. It is mainly due to the small number of hair boards and keels, and the lack of nails on the board and floor nails. Because the keel and the hair board are not firmly mounted, the concealed structure is displaced. 2. The main reason for the unevenness of the surface is the unevenness of the grass roots or the deformation of the floor planks. During construction, the level of the keel is leveled with a level ruler, and if it is not, it should be adjusted. Ventilation slots should be made on the keel. A 10 mm ventilation gap should be left on the board margin wall. The insulation material must be dry to prevent the wood from picking up the damp drum. In general, after the floor is laid, 2.5-3 cm of expansion joints should be left on the floor. Expansion joints are adjusted according to local temperature differences and climate. 3. Reasons for lax seams In addition to the non-standard installation during construction, the large width and dimensional errors of the plates are also important reasons. 4. The main reason for the partial buckling is not only due to the moisture deformation of the board, but also the patchwork seams of the wool board are too small or seamless, and the water leaking from the hoses during use is caused by wet floors. After the floor is covered, the paint on the floor paint should be complete. In daily use, water should be prevented from flowing into the lower part of the floor, and the surface water must be cleaned in time. If there is water on the floor, it must be removed within 30 minutes. 5. Sports wood flooring should use environmental protection tools during the cutting process to avoid the hazards caused by harmful substances such as sawdust, dust and formaldehyde.
Usage: Household, Washing Dish, Kitchen, Car,Bathroom, Pet and More.
Bump design-anti-slip particles inside the glove.
High temperature resisitance-the glove are heat resistance to 220 degrees and can be sterilized by boiling water.
Silicone Gloves Silicone Mitts,Silicone Oven Mitts,Silicone Oven Gloves,Silicone Cooking Gloves YANGJIANG SHENGHAI INDUSTRIAL&TRADING CO., LTD , https://www.shenghaiyj.com