1. Continuous supply with miscellaneous cards. Result: Missing ink cartridges, lack of color, horizontal stripes, color cast, anyway, can't produce decent things. Suggestion: Choose a brand with a good reputation. I haven't used any other brands. I only use Tianwei's now. I never block the head and lack color. I don't think there will be any problems with other big brands. Liansu is not a high-tech, I know Tianwei, another ghost, Huifeng, color spray crazy, how good. Continuous supply 2. Miscellaneous brand ink. At the beginning, I even bought a small brand of ink, and there was a color cast when I tried it. Absolutely can not do business. The color of the ink of Tianwei is not the best, but it is stable. Put it for a month or two and use it to take photos. The color of the grid is relatively correct; but sometimes it will be blocked. It is always cleaned and the price is cheap. These two brands. 3. The position of the ink supply tube is not correct. There is a fixed clip on the general catheter. Fix the catheter on the printer. Note that this position is best to buy the position marked with the instructions. Generally in the center of the printer, put the catheter from this position to the length of the ink cartridge. Up to about half of the printer, it can't be too long or too short. If it is long, it is easy to get stuck, while if it is short, it will not be able to move fully, which may damage the printer. 4. There are usually two holes on the supply: the big one is for plugging with ink; the small one is for air intake and should be opened when using the printer. Making a continuous confession to someone, he told me that the color of his printer was getting lighter and lighter, and when I took a look, the air inlet did not open. 5. Don't remove the transparent plastic seal on the ink cartridge, and go directly to the printer. A buddy in the group peeled it off, and the ink leaked in a mess. Later, it was sealed with transparent plastic, and I could barely continue to use it. I don't know when it will be used. 6. The air bubbles in the ink pipe should be cleaned. If there are bubbles, it is easy to break the line, color deviation, and less color failure. I do n’t understand it and think that the print head is blocked. 7. When the printer is not in use, be sure to call the printer to reset automatically. Do not unplug the power supply directly without special circumstances. The ink cartridge is not reset, and it is easy to block the ink head. Other failures are not yet understood. 8. Find a tool for clearing printers on the Internet, which is usually used by novices from one month to two months. The print head is always easy to fill up, so be prepared. When both red lights are flashing, you cannot print, and it's time to use it. 9. After everything is normal, experiment with various printing modes on the paper you use to find the best printing solution. 10. When printing photos, be careful not to use high-speed printing. There will be horizontal stripes. 11. High-quality photos are generally sufficient for taking photos (r210) No matter how high it is, it is useless. 12. If you don't calculate the cost, printing photos with rc photo paper is much better. Probably 13-15 / bag is 3-5 yuan more expensive than ordinary, rc photo paper can not be coated with cold film. If pigment ink is used, rc is recommended, and with dye, high gloss is recommended, and then cold laminating film is used. 13. Select photo paper. If it is not a very big photo paper, it is best to use RC photo paper if the quality of the photo is good. The print is shiny, has a certain degree of water resistance, and is more beautiful than high-gloss photo paper. Photo paper with a very white print surface is not good photo paper. Even if I use dyes now, I use high-gloss paper and cold laminating film to prevent water. If you use pigments, RC should be good. 14. The 210 printer does not feed well. Disassemble the rear seat, find a tension spring, and replace it with a higher tension, it will be very useful. If it is tied up, the paper can be fed smoothly, but it can only be fed manually. After a long time, the printer gear may be damaged. 15. If you don't want PS and want to process photos well, it is recommended to use ACDSEE8.0 and light and shadow magic hands together. Generally, one week of practice can process very good photos. Both softwares have online installation-free green versions. ACD is mainly used for cropping, printing, and speckle removal; light and shadow magic hands magnify images, fill light, etc., which is very useful. 16. Don't wait for ink to run out before refilling. Ink should be injected about 1/4 of the time remaining, and it is best to take a break at night. After the ink is filled, the bubbles in the ink will disappear after standing for an hour or two. Try not to refill the ink when printing. 17. The continuous supply of air bubbles in the ink guide tube is usually bad if it is not installed incorrectly. Editor in charge: Sun Wenhui Soft Sanitary Napkin,Sanitary Napkin Price,Low Cost Sanitary Napkins,Daily Dry Sanitary Napkin Shandong Tianzige International Trade Co., Ltd , https://www.sdbabydiapers.com
