Shanghai Haozhuang Instrument Co., Ltd. develops the LNB brand biochemical incubator, which is energy-saving and environmentally friendly, leading the country. Professional manufacturing is more secure and affordable Instructions for use: 1. Place the incubator on a flat and solid ground, adjust the two supporting screws at the lower end of the box to make the box stable. 2. Plug in the power socket (the power supply should be well grounded), press the "power switch", the display is on, at this time the display shows the actual temperature inside the incubator and its working time. 3. Time setting: Time setting includes the setting of "minute" and "hour". Press the "SET" setting key, when the decimal point in the lower right corner of the display position of the "minute" digital tube lights up, that is, enter the "minute" setting state, and then press the "â–²" or "â–¼" key to confirm the "incubator" work this time. Minutes â€time (the longest is 59 minutes); press the“ SET â€key again, when the decimal point in the lower right corner of the“ hour â€nixie tube display is lit, it enters the“ hour â€setting state, then press“ â–² â€or“ â–¼ "Key to confirm the" hour "time (maximum 99 hours) of the incubator's current work. 4. Temperature setting: Press the "SET" key, when the decimal point in the lower right corner of the last digit of the temperature display lights up, it enters the temperature setting state, and then press the "â–²" or "â–¼" key to confirm the incubator. Sub-set temperature (set temperature range is 5 ℃ ～ 50 ℃). When the above steps 3 and 4 are completed, press "ENTER" to confirm the working time of the incubator and the working temperature (set temperature) in the incubator. Note: After the temperature setting is confirmed, the temperature cannot be set back and forth at random, so as to avoid the compressor starting frequently, causing the compressor to overload, and affecting the service life of the compressor. 5. If you need to check the working time and temperature set by the incubator this time, press the "SET" key, the display panel will display the set time and temperature, and then press the "ENTER" key, the display value of the incubator returns To the original working state. 6. If lighting is needed in the incubator, press the "lighting switch"; if lighting is not needed in the box, the lighting switch on the panel should be placed in the "off" position to avoid affecting the upper temperature. Matters needing attention and maintenance: 1. When the use temperature is low, condensate will be generated in the incubator, and the accumulated water in the bottom water tray at the bottom of the box should be drained regularly. 2. In order to maintain the beauty of the equipment, do not use acid or alkali and other corrosive materials to wipe the surface of the box, and dry the inside of the box with a dry cloth regularly. 3. The power supply used must have a reliable ground wire to ensure that the ground wire of the incubator is in reliable contact with the ground wire of the network power supply to prevent damage caused by electrical leakage or accidental network power supply. When the incubator is stopped, the power plug should be unplugged. 4. The minimum distance between the incubator and the wall should be greater than 10cm to ensure good cooling of the refrigeration system. 5. The room should be dry, well ventilated, the relative humidity should be kept below 85%, there should be no corrosive substances, avoid direct sunlight on the incubator Shanghai Haozhuang Instrument Co., Ltd. is a technologically innovative high-tech enterprise based in Shanghai and radiating the whole country. The company has first-class technical personnel and a good team of technicians, with advanced technology and strong development strength. Since the establishment of the company, the products and The service is recognized by customers and has a good reputation. The company adheres to the business philosophy of "integrity. Professionalism. Innovation. Growth" to provide customers with elaborate services. The company's main business and production scope include: testing equipment, laboratory equipment, cleaning equipment, Environmental protection equipment and undertake the design and customization of non-standard products and provide related technical services.
The Anomatic series of high-quality deep drawn Aluminum Canisters is designed to be compatible with your chosen valves, Actuators and drug formulations. Our deep drawing process ensures a consistent side wall thickness using high strength aluminum which is far superior to other forming methods. The aluminum is work hardened during the deep draw process and the surface mechanically polished providing a smooth, hard internal finish suitable for use with both CFC and HFA propellants.
Aluminum anodization is an electrochemical process that enhances the strength, durability, and appearance of aluminum. When aluminum is oxidized, super-strong oxide (anodic) layers [grow" on the surface of the metal. These new layers are highly resistant to wear and corrosion.
The exacting part to part consistency achieved with our unique anodizing system cannot be obtained with conventional hoist line systems. Conventional anodizing systems present parts with varied coating thicknesses and voids formed due to air pocketing.
Aluminum Canisters Anomatic(suzhou)metal packaging co,ltd , https://www.anomaticpharma.com